Dies ist eine alte Version des Dokuments!


FIXME This page is not fully translated, yet.

Analoge Uhr

Der „Analoge Uhr“ Effekt erzeugt eine analoge Uhr auf dem Videobild. Die Uhr läuft in Echtzeit, wenn der Videoclip läuft. Wie die Uhr läuft und das Aussehen kann sehr flexibel eingestellt werden:

  • Vorwärtslauf, Rückwärtslauf
  • Startzeit, Endzeit
  • Geschwindigkeit
  • Farbe der Uhr
  • Farbe der Zeiger

Installation

Der „Analoge Uhr“ Effekt ist Teil der „Uhreffekte“ Plugins „clock effect“ ClockDisplay RTFxV2. Die neueste Version kann hier heruntergeladen werden: Uhr Effekt Plugin.

Auswahl des Uhr Effekts

Der Uhr Effekt ist in den Effekteinstellungen von Pinnacle Studio unter „Addons“ - „HLClockFX“ zu finden:

Nach der Auswahl von „HLClockFX“ werden 3 Effekte angezeigt:

  • Analoge Uhr
  • Digitaluhr
  • Frame TC

Parameter Einstellungen - Analoge Uhr

Das folgende Bild zeigt den Effekt Dialog nach Auswahl des „Analoguhr“ Effekts.

Folgende Parameter können eingestellt werden:

Die Parameter werden in den folgenden Kapiteln erläutert:

Position/Grösse

Mit den ersten 2 Parametern kann man die X- und die Y-Position der Uhr auf dem Videobild festlegen.

Parameter Einheit Minimum Maximum Beschreibung
X-Position Prozent 0 100 X-Position des Uhr Mittelpunktes 0% = linke obere Ecke
Y-Position Prozent 0 100 Y-Position des Uhr Mittelpunktes 0% = linke obere Ecke
Grösse Prozent 0 100 Y-Position des Uhr Mittelpunktes 0% = linke obere Ecke

Start Time

Normally the clock starts at the beginning of each clip with the time 00:00:00. 
With the Start Time sliders the starttime of the clock can be changed to any value of the day.

There are sliders for

  • hour - 0 to 23
  • minute - 0 to 59
  • seconds - 0 to 59

Stop Time

With the Stop Time sliders a stop time for the clock can be set.

There are sliders for 
* hour - 0 to 23
* minute - 0 to 59 
* seconds - 0 to 59
The clock stops exactly at the specified time.
If the clock runs forward the stop time has to be higher than the start time. 
Otherwise the clock will not start running.
If the clock runs backwards the stop time has to be lower than the start time. 
Otherwise the clock will not start running.

Time Parameters

  • Count Down

When this check box is set, the clock runs backwards from start time down to 0 or to the Stop Time.

  • Speed Factor

this slider allows to accelerate or slow down the clock.

Positive values are multiplied - i.e 10 = 10 times normal speed
Negative values are divided - i.e. -10 = 1/10th of normal speed
  • Time base

defines if the displayed time is based on the elapsed time from the start of the clip

the effect is attached to or   is based on the time from the start of the movie.
Be careful when using this parameter. 
When the clip with the clock effect is moved on the timeline and the time base is set 
to "MOVIE" the time displayed by the clock changes according to the position on the timeline. 
This is due to the fact that the time displayed by the clock is derived from the timecode 
of the frame on the timeline.

Colors

Determines the foreground or background colors of the clock. The colors are in RGB values. They can be set via via the color selection tool or the eyedropper tool.

  • Foreground Color

Color of the clock handles.

  • Foreground Opacity

Opacity of the foreground (0 = transparent, 100 = fully opaque)

  • Background Color

Color of the background

  • Background Opacity

Opacity of the background (0 = transparent, 100 = fully opaque)

  • Show Background

When „Show Background“ is switched off the background is not visible anymore.

Second Hand Parameters

  • Show Second Hand

When „Show Second Hand“ is switched off the Second Hand is not visible anymore.

  • Color

Here you can set an individual color for the Second Hand. This color becomes active

when the parameter "Use Color" is selected.
* Use Color
When this parameter is selected the individual color set for the "Second Hand" becomes active.
* Width
Determines the width of the Second Hand
* Length
Determines the length of the Second Hand

Minute Hand Parameters

  • Show Minute Hand

When „Show Minute Hand“ is switched off the Minute Hand is not visible anymore.

  • Color

Here you can set an individual color for the Minute Hand. This color becomes active

when the parameter "Use Color" is selected.
* Use Color
When this parameter is selected the individual color set for the "Minute Hand" becomes active.
* Length
Determines the length of the Minute Hand

Hour Hand Parameters

  • Show Hour Hand

When „Show Hour Hand“ is switched off the Hour Hand is not visible anymore.

  • Color

Here you can set an individual color for the Hour Hand. This color becomes active

when the parameter "Use Color" is selected.
* Use Color
When this parameter is selected the individual color set for the "Hour Hand" becomes active.
* Length
Determines the length of the Hour Hand

Point Parameters

  • Show Point

When „Show Points“ is switched off the Points are not visible anymore.

  • Show Minor Point

When „Show Minor Points“ is switched off the Minor Points are not visible anymore.

  • Color

Here you can set an individual color for the Points. This color becomes active

when the parameter "Use Color" is selected.
* Use Color
When this parameter is selected the individual color set for the "Points" becomes active.
* Width
Determines the width of the Points
* Length
Determines the length of the Points

Examples


Andere Sprachen
QR-Code
QR-Code de:analogue_clock (erstellt für aktuelle Seite)